|
aHR0cDovL2ZyZWVzaGlwLmNvLmty
- ºê·£µå À̸§: LanYuXuan
- ±Ù¿ø: CN (Á¤Ç°)
- Áõ¸í¼: ¼¼·ý
- Model Number: MCSB-1000mm
- Type: Ultrasonic Sensor
- Place of Origin: Guangdong, China
- Brand Name: MIRAN
- Usage: Displacement Position Sensor
- Theory: Ultrasonic
- Output: Analog
- Description: Ultrasonic Sensor
- Measuring range: 50~1000mm
- Blind area: 60mm
- Standard test board: 300x300mm
- Resolution: 0.35mm(max)
- Beam angle: 10-15¡Æ
- Linearity: 0.1%
- Frequency: 200KHz
- Working voltage: 15~30VDC
- Power consumption: 20MA
- Protection Degree: IP67
Miran Ultrasonic Sensor MCSB-1000mm Distance Analog Output Sensor
Overview MIRAN MCSB ultrasonic distance sensor is a kind of mechanical wave whose vibration frequency is higher than that of sound wave.It¡¯s development depends on the theory that the transducer crystals chip vibrates under the excitation of voltage and then combine with the characteristics of ultrasonic wave. It has the characteristics of high frequency, short wavelength, small diffraction phenomenon, especially good directivity, and be the directional propagation of radiation.
Applications Distance measurement, liquid level measurement, height measurement, interval measurement, size measurement, material accumulation height measurement, filler level measurement, filler level detection,Diameter and Speed Measurement, Profile Measurement, Tension Control, Packaging Detection, Object Counting etc.
Product size drawing (unit :mm)
Installation Firstly, the sensor is electrified, and the red and yellow lights behind the sensor will light up. Yellow light means: yellow light is unchanged, the object is within the measurement range; Blinking yellow light ,Set object detected in the set function state. Red light means : red light is always on, power is on; long dark, error red light flashing ,No object detected in the set function state. This sensor has two analog output modes (rise and fall modes) as shown below: A: Setting the farthest distance P2: 1. Place a test object where you want to set the distance. 2. Pry the gray line (adjustment line) and the brown line (power supply) together , during this time if the measured object is captured, the yellow light will always flash. After this state lasts for four to five seconds, please removed the gray line. The setting is successful. B Set the nearest distance P1: 1. Place a test object where you want to set the distance. 2, please tie the gray line (adjustment line) and the blue line (power supply negative) together. during this time, if the measured object is captured, the yellow light will always flash. After this state lasts for four to five seconds, pls removed the white line. The setting is successful. Note: The yellow light and the red light may flash together during the setting process, indicating that the sensor does not accurately capture the measured object. Need us to move the sensor slightly to align the measured object.Until the yellow light flashes continuously. (Please noted that this setting process must be completed within 3 minutes, otherwise the sensor will be locked. If the sensor is locked ,you need to disconnect the power supply and re-power. Then reset it).
Notes 1. Since the ultrasonic sensor is directional, it is important to pay attention to its mounting position. It is recommended that it should be straight between the installation position and the tested object. In this situation the measurement data will be more accurate.(with mounting nut)
2. The sensor is a precision instrument. Do not scratch the surface.
3. When using the sensor, please make sure about the power supply and ripple voltage.
4. When using the sensor, there must be no strong mechanical vibration, and the working environment should not have strong electromagnetic interference.
5. The sensor cannot be used in the vacuum zone or in the explosion-proof zone.
6. please don not use the sensor near by the water, steam, acid, solvents which is above 50¡É¡£
7. The sensor shall not be dismantled without permission, and the company will not bear any consequences if it is damaged by private disassembly.
Pre-sale servie:
* Inquiry and consulting support.
* Sample testing support.
* Factory visit
After-Sales Service.
* Training to instal and use.
* Quick response to technical problems;
Dear Friends:
Shenzhen Miran Technology Co., Ltd. is the largest supplier of Linear Position Sensors in China .The company was founded in 2003, which is also the first sensor manufacturer in China. Miran specialized in Linear Positon Sensors.
Miran now develops and manufactures a wide range of Linear Position Sensor (brand:MIRAN,LinecSKI,WANSUNG), Wire Rope Potentiometer,Magnetostrictive Liquid Level Sensor,Angular Sensor,Lubricating Pumps(Oil/Grease/Butter),LVDT,Eddy Current Sensor, and many other motion control products to support many different industrial applications.
Miran Products are widely used in injection molding machines,die casting machines,rubber machines,footwear machines,EVA injection machines,bottle blowing machines,woodworker machines, hydraulic machinery,level control, suspension stroke control,construction machinery,seaport machinery,industrial robots,etc.
As a leading manufacturer in China, Miran has the faith to keep our customers in the lead.Miran is approved by ISO9001:2008, CE, CCC, Rohs certifications. Also we are very proud of the following
1. Being among the leading manufacturer we contribute in R&D of related industry, We spend millions every year for developing new tech and new products.
2.We Promise high quality with strict QC. We performed vibration test, low and high temperature test,electromagnetic interference regulatory test,endurance test, and explosion proof test for each product before shipping.
3. Lean Production is intruduced to factory.
4. Excellent performance in on time delivery.
5. Excellent sales & after-sales service.
Miran now provide the service to customize product logo .
If you have any suggestion or question Please let us know.
Http://miran-tech.en.11.com/
Http://www.miransensor.com/
|
|
|
|
|