Note
1. It is a radio. If the radio is not received, there will be white noise. You need to adjust the receiving radio by pressing the button.
2. Don`t use it in an environment with interference, otherwise there will be a lot of white noise.
3. The frequency can be adjusted. The signal of each frequency is strong or weak. If it is a relatively weak signal, this frequency cannot be played clearly.
4. Is there any noise in the headset? If there is noise, the radio station may not be searched.
5.It is recommended not to use it in an environment with interference. You can try it outdoors. The indoor reception signal is easily interfered.
DIY Kit FM Stereo Radio Module Adjustable 76-108MHz Wireless Receiver DC 3V
1.Introduction:
The YFM-2 type radio circuit is very simple. The total number of components does not exceed 19. Although the number of components is not large, it includes two types of components: SMD and DIP which are suitable for novices and friends who want to practice soldering of SMD components.
2.Feature:
1>.Built-in digital automatic gain control (AGC) circuit
2>.Support the global frequency band 76-108Mhz
3>.DIY manual welding
4>.Simple and easy to operate
5>.Support radio memory function
3.Parameter:
1>.Item name: FM Stereo Radio Module DIY Kit
2>.Item Mode:YFM-2
3>.Work Voltage:DC 3V
4>.Work Current:19mA
5>.Work Frequency:76-108Mhz
6>.Output impedance:32ohm
7>.Work Temperature:-40¡É~85¡É
8>.Work Humidity:0%~95%RH
9>.Size(Installed):57*32*20mm
4.Application:
1>.Training welding skills
2>.Student school
3>.DIY production
4>.Project Design
5>.Electronic competition
6>.Graduation design
7>.Crafts collection
8>.Home decoration
9>.Souvenir collection
5.Installation Tips:
1>.User needs to prepare the welding tool at first.
2>.Please be patient until the installation is complete.
3>.The package is DIY kit.It need finish install by user.
4>.The soldering iron can`t touch the components for a long time(1.0 second), otherwise it will damage the components.
5>.Pay attention to the positive and negative of the components.
6>.Strictly prohibit short circuit.
7>.Install complex components preferentially.
8>.Make sure all components are in right direction and right place.
9>.It is strongly recommended to read the installation manual before starting installation!!!
6.Installation Steps(Please be patient install!!!):
1>.Step 1: Install 1pcs SOP-16 RDA5807PF at U1.There is a dot on one corner of the IC and there is a rectangle pad on PCB where the Pin1 of IC can place on.These two marks are corresponding to each other and are used to specify the installation direction of the IC.
2>.Step 2: Install 1pcs 30K ohm Resistor at R1.
3>.Step 3: Install 1pcs 0.1uH Inductor at L1.
4>.Step 4: Install 2pcs 1uH Inductor at L2,L3.
5>.Step 5: Install 1pcs 32.768KHz Crystal Oscillator at Y1.
6>.Step 6: Install 1pcs 24pF Ceramic Capacitor at C1.
7>.Step 7: Install 1pcs 0.01pF(103) Ceramic Capacitor at C2.
8>.Step 8: Install 1pcs 0.022pF(223) Ceramic Capacitor at C3.
9>.Step 9: Install 5pcs 6*6*5mm Switch at S1-S5.
10>.Step 10: Install 1pcs 100uF 16V Electrolytic Capacitor at C4,C5. Please pay attention to the positive and negative poles. The shorter pin is the negative pole.
11>.Step 11: Install 1pcs 3.5mm Audio Jack at J1.
12>.Step 12: Connect battery box.Pay attention to positive and negative.
13>.Step 13: Use a cable tie to fasten the battery box.
14>.Step 14: Connect to power supply and enjoy the effect.
About the Product:
1>. Train electronic welding skills
The DIY FM Radio Soldering Kit will help you learn the basics of working with printed circuit boards, while helping you become familiar with various electronic components and develop good soldering skills!
2>.Low power consumption
The digital automatic gain control (AGC) circuit is adopted to make the received signal more stable! In addition, the total current is about 19mA when using two AA batteries.
3>. Power failure memory function
It supports the radio station memory function, the next time you turn on the device, it will automatically return to the last time you turned off the radio station and volume.
4>.Transparent silk screen for component installation
There is a transparent silk screen on the PCB for component mounting to help you solder, especially for epoxy PCB soldering for students, not ordinary cardboard!